PollyBD Networking Blogspot
C-Data Technology is a high-tech enterprise specialized in the research and manufacture of broadband networking access equipment. Currently our product series includes GPON, EPON. By combining IP technology and radio frequency modulation technology, voice, data and video service are integrated.
Contents
- OVERVIEW……………………………………………………………………………. 8
- COFIGURATION PREPARATION……………………………………………………………. 10
- CLI COMMAND MODE…………………………………………………………………. 11
- SYSTEM MANAGEMENT………………………………………………………………. 13
Backup OLT Configuration File…………………………………………………………….. 14
Restore OLT configuration from PC………………………………………………………….. 15
Backup ONU Configuration File…………………………………………………………….. 15
Restore ONU Configuration File from PC……………………………………………………… 16
Backup OLT/ONU Configuration File automatically………………………………………….. 16
Factory Default Configuration……………………………………………………………. 17
Save Configuration………………………………………………………………………. 17
Show current running- configuration………………………………………………………… 17
Show current startup-configuration……………………………………………………….. 18
Reboot System………………………………………………………………………… 18
system update OLt ‘s firmware…………………………………………………………….. 18
upgrade all onu(s) by CTCS………………………………………………………………… 19
Backup Log…………………………………………………………………………… 19
Flush log……………………………………………………………………………… 20
SNMP Read Community……………………………………………………………….. 20
SNMP Write Community………………………………………………………………….. 20
Trap IP Configuration………………………………………………………………… 21
Network Parameter Configuration……………………………………………………. 21
Management VLAN Configuration……………………………………………………. 22
Configure system mtu………………………………………………………………… 22
Configure system time automatically by NTP…………………………………………. 22
Configure system time manually……………………………………………………… 23
- SHOW SYSTEM CONFIGURATION…………………………………………………………………………………………………………. 23
Show system infor……………………………………………………………………. 23
Show system ipconfig…………………………………………………………………. 24
Show system log……………………………………………………………………… 24
Show system memory…………………………………………………………………. 25
Show system mgmt-vlan……………………………………………………………… 25
Show system snmp……………………………………………………………………. 26
- CONFIGURE SYSTEM ONU TEMPLATE………………………………………………………………………………………………… 26
Enable/Disable system ONU template CATV port……………………………………… 26
Enable/Disable system ONU template fec function……………………………………. 26
Enable/Disable system ONU template igmp fast-leave function……………………….. 27
configure system ONU template igmp mode………………………………………….. 27
Enable/Disable system ONU template VOIP port………………………………………. 28
- CONFIGURE USER ONU TEMPLATE…………………………………………………………………………………………………… 28
Enter user ONU template config mode………………………………………………… 28
configure user ONU template capacity………………………………………………… 28
Enable/Disable user ONU template user port…………………………………………. 29
configure user ONU template egress-policing…………………………………………. 29
configure user ONU template ingress-policing………………………………………… 30
Enable/Disable user ONU template auto negotiation function…………………………. 30
Enable/Disable user ONU template auto flow control function…………………………. 30
Enable/Disable user ONU template auto loop-detec function………………………….. 31
configure user ONU template mac aging-time………………………………………… 31
configure user ONU template statistics function………………………………………. 31
- SWITCH CONTROL CARD CONFIGURATION………………………………………….. 32
- STORM CONTROL……………………………………………………………………………………………………………………….. 32
Enable/Disable Storm Control and Configure the Storm Control Parameter…………….. 32
- PORT MANEGEMNET…………………………………………………………………………………………………………………….. 32
enter switch port config mode………………………………………………………… 32
Port parameters……………………………………………………………………… 33
Configurate the pvid of port………………………………………………………….. 34
Configurate auto-nego of port………………………………………………………… 35
Configurate the speed of port………………………………………………………… 35
Add vlan list of port…………………………………………………………………… 35
Delete the vlan list of port……………………………………………………………….. 36
Show swport current configuration information………………………………………. 36
Configuration ingress-port rate………………………………………………………. 36
Configuration egress-port rate……………………………………………………….. 37
- CONFIGURE SWITCH MODE……………………………………………………………………………………………………………… 37
Show vlan state………………………………………………………………………. 37
Configure vlan enable/disable……………………………………………………….. 37
- MAC ADDRESS MANAGEMENT………………………………………………………………………………………………………… 38
Configure mac-address aging timeout………………………………………………… 38
Show mac-address aging……………………………………………………………… 38
- VLAN CONFIGURATION MANAGEMENT………………………………………………………………………………………………….. 38
Creat vlan……………………………………………………………………………. 38
Add vlan port member………………………………………………………………… 39
Delete vlan port member…………………………………………………………….. 39
Delete vlan…………………………………………………………………………… 39
Show vlan configuration of vlan………………………………………………………. 40
- RSTP CONFIGURATION MANAGEMENT…………………………………………………………………………………………………… 40
Enable/disable RSTP configuration…………………………………………………… 40
Configure Rstp bridge maxage aging time……………………………………………. 41
Configure Rstp bridge delay time…………………………………………………….. 41
Configure Rstp bridge prioprity……………………………………………………….. 42
Configure max counts of Rstp packet per second……………………………………… 42
Configure Rstp port piority……………………………………………………………. 42
Configure Rstp port path-cost………………………………………………………… 43
Configure Rstp edge-port…………………………………………………………….. 43
Configure Rstp p2p port………………………………………………………………. 44
Configure Rstp protocol version check………………………………………………… 44
Show Rstp information……………………………………………………………….. 45
- TRUNK CONFIGURATION MANAGEMNET…………………………………………………………………………………………………. 45
Enter trunk config mode……………………………………………………………… 45
Add port of trunk member……………………………………………………………. 46
Delete port of trunk member…………………………………………………………. 46
Delete trunklist configuraion…………………………………………………………. 46
Show trunk information………………………………………………………………. 47
- RMON NETWORK MONITORING AND CONFIGURATION……………………………………………………………………………………. 47
rmon history configration…………………………………………………………….. 48
rmon event configuration…………………………………………………………….. 49
rmon alarm configuration……………………………………………………………. 50
Show rmon statistics information…………………………………………………….. 51
Show rmon history information……………………………………………………….. 51
show rmon event information………………………………………………………… 52
Show rmon eventlog information…………………………………………………….. 52
Show rmon alarm information………………………………………………………… 53
- MIRROR PORT CONFIGURATION MANAGEMENT………………………………………………………………………………………….. 53
Enable/disable mirror fuction………………………………………………………… 53
Configure mirror source_port………………………………………………………… 54
Configure mirror dest_port…………………………………………………………… 55
Show mirror information……………………………………………………………… 55
- IGMP-SNOOPING MONITORING AND CONFIGURATION…………………………………………………………………………………….. 55
Enable/disable igmp snooping function………………………………………………. 55
Enable/disable igmp snooping fast-leave function……………………………………. 56
Enable/disable igmp snooping drop-unknown function……………………………….. 56
Configure igmp snooping host-aging-time……………………………………………. 56
Enable/disable igmp snooping querier function………………………………………. 56
Configure igmp snooping querier query interval………………………………………. 57
Configure igmp snooping querier max-response-time…………………………………. 57
Configure igmp snooping querier source_ip…………………………………………… 57
Configure igmp snooping querier router-aging-time………………………………….. 57
add/delet igmp-snooping static port………………………………………………….. 57
- CLEAR ALL LEARNED MAC ADDRESS……………………………………………………………………………………………………. 58
- OLT MANAGEMENT………………………………………………………………….. 58
- OLT BASIC CONFIGURE MANAGEMENT………………………………………………………………………………………………… 58
Enter OLT Management………………………………………………………………. 58
Enable/disable OLT port……………………………………………………………… 59
Long light checking Function…………………………………………………………. 59
Configure p2p Function………………………………………………………………. 60
Configure out-tpid Function………………………………………………………….. 60
- OLT ACL CONFIGURE……………………………………………………………………………………………………………….. 60
Delete One ACL………………………………………………………………………. 60
Delete Current OLT All ACL………………………………………………………………. 61
Add OLT ACL…………………………………………………………………………. 61
- OLT MAC MANAGEMENT……………………………………………………………………………………………………………. 62
Configure OLT MACAge Time…………………………………………………………. 62
Flush current olt’s mac table list……………………………………………………… 63
Enable OLT MAC Learening function………………………………………………….. 63
Disable OLT MAC Learning Function………………………………………………….. 63
Enable MAC Move…………………………………………………………………….. 63
Disable MAC Move……………………………………………………………………. 63
- OLT AUTH…………………………………………………………………………………………………………………………….. 64
Disable OLT Auth…………………………………………………………………….. 64
Add/Delete/Show Whitelist………………………………………………………….. 64
Add/Delete/Show Blacklist…………………………………………………………… 65
OLT hybrid Auth Mode Configure……………………………………………………… 66
OLT LOID Auth Mode Configure………………………………………………………. 67
OLT MAC Auth Mode Configure……………………………………………………….. 68
- CONFIGURE PACKET_FILTER OF OLT PON PORT………………………………………………………………………………….. 68
Packet_filter of OLT PON port about DHCP function…………………………………… 68
EOC MME packet-filter function………………………………………………………. 68
Netbios packet-filter function………………………………………………………… 68
8306_rtk_loopback packet-filter function……………………………………………. 69
- CONFIGURE TRAP ALARM AND MESSAGE ALARM FUNCTION OF ONU………………………………………………… 69
Configure message alarm about ONU off the electricity……………………………….. 69
Configure trap alarm about ONU off the electricity……………………………………. 70
- CONFIGURE QINQ FUNCTION………………………………………………………………………………………………………….. 70
Add QinQ configuration………………………………………………………………. 70
Delete QinQ configuration……………………………………………………………. 70
- CONFIGURE OFFLINE ONU………………………………………………………………………………… 71
Add offline ONU and bind the template with ONU…………………………………….. 71
delete offline ONU……………………………………………………………………. 71
- SHOW OLT CONFIGURATION INFORMATION………………………………………………………………………………………………. 72
Show olt attribute information……………………………………………………….. 72
Show olt optical information…………………………………………………………. 72
Show olt online-onu information……………………………………………………… 73
Show olt acl information……………………………………………………………… 73
Show olt auth mode information……………………………………………………… 73
Show olt port staus information………………………………………………………. 74
Show olt alarm information…………………………………………………………… 74
Show olt learning-mac information…………………………………………………… 75
Show olt p2p information…………………………………………………………….. 75
Show olt packet-filter information………………………………………………………… 75
Show olt tpid out-tpid………………………………………………………………… 76
- ONU MANAGEMENT………………………………………………………………….. 76
- SHOW ONU BASIC INFORMATION……………………………………………………………………………………………………. 76
Show Online ONU…………………………………………………………………….. 76
Show ONU Version……………………………………………………………………. 77
Show ONU Capabilities……………………………………………………………….. 77
Show ONU Optical……………………………………………………………………. 77
- ONU MANAGEMENT MODE……………………………………………………………………………………………….. 77
- ONU BASIC OPERATION AND MANAGEMENT……………………………………………………………………………………….. 78
Reboot ONU………………………………………………………………………….. 78
Deregister ONU………………………………………………………………………. 79
Configure ONU FEC…………………………………………………………………… 79
Restore ONU to Default Settings………………………………………………………. 79
Configure ONU Sys Management IP……………………………………………………. 79
Save Current ONU Configuration……………………………………………………… 80
upgrade ONU software……………………………………………………………….. 80
- CONFIGURE ONU IGMP………………………………………………………………………………… 80
ONU IGMP Global Configuration………………………………………………………. 80
Configure ONU UNI Port IGMP………………………………………………………… 81
- ENTER ONU LINK MODE…………………………………………………………………………………………………………….. 82
Configure ONU Link Upstream SLA……………………………………………………. 82
Configure ONU Link Downstream SLA…………………………………………………. 82
Configure ONU Link Acl………………………………………………………………. 83
- ENABLE/DISABLE ONU PORT ISOLATE FUNCTION ………………………………………………………………………………………… 84
- CONFIGURE ONU PON STATISTICS…………………………………………………………………………………………………… 84
- ENABLE/DISABLE ONU CATV PORT …………………………………………………………………………………………………. 84
- ENTER ONU UNI PORT MANAGEMENT MODE………………………………………………………………………………………. 84
Configure ONU Uni Port Parameters………………………………………………….. 85
Configure ONU Uni Port Vlan Mode……………………………………………………. 87
- ENTER ONU VOIP PORT MANAGEMENT MODE…………………………………………………………………………………… 91
Configure ONU VOIP Port Parameters…………………………………………………. 92
- EQUIPMENT DIAGNOSIS INFORMATION……………………………………………… 94
- PING COMMAND TEST…………………………………………………………………………………………………………………… 94
- TRACERT CHECKING THE DEVICE THE PATH OF THE HOST……………………………………………………………………………… 94
INCLUDING REMARKS…………………………………………………………………….. 95
1 Overview
Introduction
This manual is applicable to Cortina Based EPON OLT products , This document is for those who perform all tasks for the EPON OLT once it has been successfully installed. Users of this Guide should understand EPON technology and have experience configuring EPON devices.
Cortina-Based OLT system could support inband and outband network management mode and EMS network management based on SNMP.
The user can use several different network interfaces to do network management, such as those listed below:
- SNMP Management
- CLI Management
This manual introduce CLI configuration function of EPON OLT.
In the initial setup step of OLT, there are two ways based on CLI management to login system:
- Terminal Emulation of CONSOLE port (RJ-45)
- Telnet of management port (RJ-45)
Command Explanations in each Section
Commands are usually presented in the following ways:
- Tables for specific functions or features that include important parameters
- Specific commands that are part of examples
- A table at the end of each Section that includes all commands and descriptions of all parameters.
Command Presentation in Examples
When a command is presented in an example, it follows the exact syntax and parameter values that match the
example configuration. If a command is very long, a (->) is used to note the command continues on the next line.
Command Syntax
The syntax rules for a Command and its parameters use the following conventions throughout this document:
- Blackface letter indicates command itself or command keyword
- “< >” The text inside it is the required parameters
- [] = Optional The text inside it is the optional parameters
- | = Option (OR) The multiple items which are divided are multi-select required parameters, indicating that must select one of
- “<x-y>” Valus rang from x to One is selected.
Editing Functions, Keystrokes, and Abbreviations
The product supports line editing, line recall, and abbreviations, so that command line input and editing can be done very quickly once command syntax and the line editing commands are learned.
| Action | Key Sequence |
| Move cursor within command line | left and right arrow |
| Delete character to left of cursor | [Delete] or [Backspace] |
| Clear command line | [Ctrl/U] |
| Recall previous command in command history | CTRL/P or up arrow |
| Recall next command in command history | CTRL/N or down arrow |
| Automatically complete a partially entered command keyword | [Tab] or [Ctrl/I] |
2 Cofiguration Preparation
Console Port Connection
There is a Console port in the front panel of Switch Control Card .The command line configuration interface is enabled via console port connecting to the NMS’s superior terminal. Super terminal’s basic configuration is as follows:
Network Connection
EPON OLT support inband management (CAT5 connect to ge1-ge8 port) and outband management
(CAT4 cable to management port).After Telnet to CLI interface ,we can manage the GEPON products.
Defualt outband(inband) network management IP:192.168.1.100
3 CLI Command Mode
OLT CLI use the layered command structure （ Command mode ） . Every command mode provides subset of CLI command. The available CLI command depends on those command
modes which have been activated currently.
User Login EPON CLI System
System provide two login accounts default as follows:
| Username | Password |
| admin | admin |
| guest | Null |
After you log in successfully, the following interface pops up :
CLI Command Help
When the command lines shows : epon> or epon#, user can input the configuration command to mange or inquire the configuration information .
OLT CLI command provides various help and shortcut keys. Next table lists main shortcut keys of obtaining help and methods in CLI command.
CLI command Help
| Method | Function | ||||
| Type “?” in any CLI command level | Show all available commands | ||||
| Partial command+“？” | Show the initial command list of the specific character string(There is no space between the
command and the question mark ） |
||||
| Command+Space +“ ？” | Show the completer
instruction of command |
syntax | and | the | brief |
| Partial command +<tab> | System will automatically complete the command
or keyword |
||||
| Ctrl-P” or the up arrow key ↑ | Invoke the executed command previously. | ||||
For example 1: epon#?
auth – configure authentication mode for Olt igmp-snooping – configure IGMP Snooping
logout – exit the CLI system
mac-address – ctrl-card dynamic mac address table management mirror – configure switch mirror
olt – configure OLT
ping – test that a remote host is reachable
reset – reset the values
rmon – configure RMON
rstp – rapid spanning tree protocol configuration
show – show system configuration
swmode – set basic switch mode
swport – enter switch port config mode
system – configure systerm
tracert – trace the route to host
trunk – enter trunk config mode
vlan – enter vlan config mode
For example 2: epon# s?
swmode swport system show epon# s
For example 3: epon#show + [ ? ]
auth – show olt auth mode
igmp-snooping – show igmp snooping configurations
mac-address – mac-address
mirror – show switch mirror configurations
olt – show olt’s configuration
qinq – show QinQ configuration
rmon – show RMON
rstp – Display RSTP information
running-config – show current running-configuration startup-config – show current startup-configuration swmode – show swmode
swport – display port attribute information
system – show system configuration
trunk – show trunk configuration
vlan – show vlan configuration
Configure Terminal
The command mode allows the user to change equipment configuration. The changed configuration can be saved into OLT flash memory and used when system is started next time.
Configuration mode allows distributing and modifying each port separately for the specific parameters (Optical Line Terminal).
For example1: epon# swport ge1 System prompt is epon(GE-1)#
For example2: epon# olt 1 System prompt is epon(olt-1)#
ONU configuration mode is the sub-mode of configuration command mode of olt, and is used to configure the logical port parameters of ONU
For example: epon(olt-1)# onu 60 System prompt is epon(olt-1/onu-60)#
4 System Management
Change system user and password
| Command Grammar | epon#system user <old-password> <new-user> <new- password> <comfirm-password> |
| Function | Change system user and password |
| <old-password> | Old password |
| <new-user> | New username |
| <new-password> | New password |
| <comfirm-password> | Comfirm password |
configure system hostname
| Command Grammar | epon# system hostname <hostname> |
| Function | configure system hostname |
| <hostname> | System hostname |
【 Example 】
Example 1 ： setting OLT hostname is OLT
System Configuration File
Backup OLT Configuration File
| Command Grammar | epon# system configurations backup olt <tftp-server> |
| Function | Backup OLT configuration File to PC, firstly, the tftp server should be ready. |
| <tftp-server> | Tftp server ip address, eg: 192.168.1.130 |
【 Example 】
Example 1 ： Backup OLT configuration file to PC ：
Restore OLT configuration from PC
| Command Grammar | epon# system configurations download olt <tftp-server>
<filename> |
| Function | Restore OLT configuration from PC, firstly, the tftp server and configurefile should be ready. |
| <tftp-server> | Tftp server ip address, eg: 192.168.1.130 |
| <filename> | The Configuration File.
eg: olt_cfg_backup_20000101055726.tar.gz |
【 Example 】
Example 1 ：Restore OLT configuration from PC：
Backup ONU Configuration File
| Command Grammar | epon#system configurations backup onu <tftp-server> |
| Function | Backup ONU configuration File to PC, firstly, the tftp server should be ready. |
| <tftp-server> | Tftp server ip address, eg: 192.168.1.130 |
【 Example 】
Example 1 ： Backup ONU Configuratin to PC ：
Restore ONU Configuration File from PC
| Command Grammar | epon#system
<filename> |
configurations | download | onu | <tftp-server> |
| Function | Restore ONU configuration from PC, firstly, the tftp server and configurefile should be ready. | ||||
| <tftp-server> | Tftp server ip address, eg: 192.168.1.130 | ||||
| <filename> | The Configuration File.
eg: olt_cfg_backup_20000101055726.tar.gz |
||||
【 Example 】
Example 1 ： Restore ONU configuration from PC ：
Backup OLT/ONU Configuration File automatically
| Command Grammar | epon# system configurations auto-backup <admin>,<backup- type>, <interval>,<server> |
| Function | Backup OLT/ONU configuration File to PC automatically, firstly, the tftp server should be ready. |
| <admin> | Disable: close auto-backup function Enable:open auto-backup function |
| <backup-type> | <olt | onu | all > |
| <interval> | Auto-backup interval,<1-365> day |
| <server> | Tftp server ip address, eg: 192.168.1.130 |
Configuration Management
Factory Default Configuration
| Command Grammar | epon# system default |
| Function | Set the device back to factory default congfiguration 。
Remark ：the device would reboot。 |
Save Configuration
| Command Grammar | epon# system save <all> or <olt> |
| Function | Save device configuration 。 |
| <all> | Take this parameter will save all device ，include all olt and all onu. |
| <olt> | Take this parameter only save olt configuration. |
Show current running- configuration
| Command Grammar | epon#show running-config <all> ,<auth>, <olt>,<onu> or <swith> |
| Function | show current running-configuration |
| all | show current all running-configuration Include OLT and ONU |
| auth | show current auth running-configuration |
| olt | show OLT running-configuration |
| onu | show ONU running-configuration |
| swith | show current swith running-configuration |
Show current startup-configuration
| Command Grammar | epon#show startup-config <all> ,<auth>, <olt>,<onu> or <swith> |
| Fuction | show current startup-configuration |
| all | show current all startup-configuration |
| auth | show current auth startup-configuration |
| olt | show olt startup-configuration |
| onu | show onu startup-configuration |
| swith | show current switch startup-configuration |
Reboot System
| Command Grammar | epon# system reboot |
| Function | Reboot OLT. |
Sytem update firmware
system update OLt ‘s firmware
| Command Grammar | epon#system update firmware <firmware> tftp-server <ip> |
| Fuction | Sytem update olt’s firmware
Tftp server and firmware file should be ready |
| <firmware> | update system firmware |
| <ip> | tftp server IP address |
upgrade all onu(s) by CTCS
| Command Grammar | epon#system update onu <tftp-server> <file> <type> |
| Fuction | upgrade all onu(s) by CTC
Tftp server and firmware file should be ready |
| <tftp-server> | tftp server IP address |
| <file> | image name |
| <type> | device type |
Log Management
Backup Log
| Command Grammar | epon#system log backup <server-ip> |
| Function | Backup system log to PC, firstly, tftp server should be ready. |
| <server-ip> | Tftp server ip address, eg: 192.168.1.130 |
【 Example 】
Example 1 ： Backup system log to PC ：
【 Example 】
Example 2 ：Show system all log：
Flush log
| Command Grammar | epon#system log flush |
| Function | Flush all system log. |
【 Example 】
Example 1 ： Flush system all log ：
SNMP Management
SNMP Read Community
| Command Grammar | epon# system snmp community read-only <community> |
| Function | Set SNMP Read Community. |
| < community > | Read Community ， the string’s length should not lenger than 16 chars. eg ： public 。 |
SNMP Write Community
| Command Grammar | epon# system snmp community read-write <community> |
| Function | Set SNMP Write Community . |
| < community > | Write Community ，the string’s length should not lenger than 16 chars. eg ：private 。 |
Trap IP Configuration
| Command Grammar | epon#system snmp trap-ip <index> <ip-addr> |
| Function | Set the SNMP Trap IP Address, could set up to 4 trap ip |
| <index> | index : 1-4 。 |
| <ip-addr> | IP Address. Eg: 192.168.1.130 |
Network Address Management
| Command Grammar | epon#system ipconfig |
| Function | Configure the Network Address of inband and outband manage IP. |
【 Example 】
Example 1 ： Show command parameter
epon#system ipconfig // enter“ ？”
<ip> – ip address, example: 192.168.0.233
<netmask> – netmask address, for example: 255.255.255.0
<gateway> – gateway Network Parameter Configuration
| Command Grammar | epon#system ipconfig <ip> <netmask> <gateway> |
| Function | Configure inband and outband management IP address netmask gateway 。 |
| < ip> | IP address. eg: 192.168.1.100 |
| <netmask> | Netmask. eg: 255.255.255.0 |
| < gateway > | Gateway. eg: 192.168.1.254 |
【 Example 】
Example 1 ： Confgiure the manage ip to 192.168.1.100 ， netmask to: 255.255.255.0， gateway to 192.168.1.254 ：
|
Example 2 ： Show the Network IP address Parameter
Management VLAN Configuration
| Command Grammar | epon# system mgmt-vlan < vid> |
| Function | Configure the management vlan id. |
| < vid> | VLAN ID: 1 ～ 4094 |
Configure system mtu
| Command | epon# system mtu <mtu> |
| Grammar | |
| Function | Configure system maximum transmission unit. |
| <mtu> | Scope:<1518-2047>, unit: byte |
configuration
Configure system time automatically by NTP
| Command Grammar | epon# sys date ntp <admin> <interval><server>or<timezone> |
| Function | Configure system time automatically by NTP |
Configure system time manually
| Command Grammar | epon# system date manual <time> |
| Function | Configure system time manually |
| <time> | Time format: YYYY.MM.DD-hh:mm:ss |
【 Example 】
|
Example1 ： manually systime is 2015.12.12 10h:10m:10s
show system configuration
Show system infor
| Command Grammar | epon# show system infor |
| Function | show system infor |
【 Example 】
|
Example1： show device system infor
Show system ipconfig
| Command Grammar | epon# show system ipconfig |
| Function | show ipconfig |
【 Example 】
|
Example 1 ： show system ipconfig
Show system log
| Command Grammar | epon# show system log <all> or <tail> |
| Function | show device system log |
| tail | show the tail of the log file |
| all | Show the all logs |
【 Example 】
Example 1 ： show the tail of the log file
epon# show system log tail
01/01/00 00:44:42 Bridge Max Age : 30
01/01/00 00:44:49 Bridge Max Age must be less than or equal to twice the the Bridge Forwarding Delay minus 1.1
01/01/00 00:44:49 Bridge Forwarding Delay : 20
01/01/00 00:44:54 Bridge Max Age must be less than or equal to twice the the Bridge Forwarding Delay minus 1.
01/01/00 00:44:54 Bridge Forwarding Delay : 20
01/01/00 00:00:22 Receive from rstp bpdu handle message queue failed! 01/01/00 00:00:25 (cdtDeviceStateSet) Slot 1 olt 1~4 deregistered.
01/01/00 00:00:25 (cdtDeviceStateSet) Slot 1 olt 5~8 deregistered. 01/01/00 00:01:15 (cdtDeviceStateSet) Slot 1 olt 5~8 registered.
01/01/00 00:01:29 (cdtDeviceStateSet) Slot 1 olt 1~4 registered.
01/01/00 00:01:40 onu-1-1-25 (llid-0,mac-e0-67-b3-07-24-0c,ctc-30)online… 01/01/00 00:00:22 Receive from rstp bpdu handle message queue failed!
01/01/00 00:00:25 (cdtDeviceStateSet) Slot 1 olt 1~4 deregistered. 01/01/00 00:00:25 (cdtDeviceStateSet) Slot 1 olt 5~8 deregistered. 01/01/00 00:01:15 (cdtDeviceStateSet) Slot 1 olt 1~4 registered.
01/01/00 00:01:29 (cdtDeviceStateSet) Slot 1 olt 5~8 registered.
01/01/00 00:01:37 onu-1-1-25 (llid-0,mac-e0-67-b3-07-24-0c,ctc-30)online… 01/01/00 00:00:22 Receive from rstp bpdu handle message queue failed!
01/01/00 00:00:23 Receive from rstp bpdu handle message queue failed! 01/01/00 00:00:26 (cdtDeviceStateSet) Slot 1 olt 1~4 deregistered.
01/01/00 00:00:26 (cdtDeviceStateSet) Slot 1 olt 5~8 deregistered. 01/01/00 00:01:16 (cdtDeviceStateSet) Slot 1 olt 1~4 registered.
01/01/00 00:01:30 (cdtDeviceStateSet) Slot 1 olt 5~8 registered.
01/01/00 00:32:14 onu-1-1-25 (llid-0,mac-e0-67-b3-07-24-0c,ctc-30)online… epon#
1
Show system memory
| Gommand Grammar | epon# show system memory |
| Function | show system memory |
【 Example 】
Example1： show system memory
Show system mgmt-vlan
| Command Grammar | epon# show system mgmt-vlan |
| Function | show system mgmt-vlan |
【 Example 】
Example 1: show system mgmt-vlan
Show system snmp
| Command Grammar | epon# show system snmp |
| Function | Show system snmp |
【Example 】
|
Example 1 ： show system snmp
Configure system ONU template
Enable/Disable system ONU template CATV port
| Gommand Grammar | epon# system onu-template-config-system catv <admin> |
| Function | enable/disable system ONU template CATV port |
| <admin> | Enable: Open the system ONU template CATV port
Disable: Close the system ONU template CATV port |
【 Example 】
|
Example1： enable system ONU template CATV port
Enable/Disable system ONU template fec function
| Gommand Grammar | epon# system onu-template-config-system ctc fec <admin> |
| Function | enable/disable system ONU template fec function |
| <admin> | Enable: Open the system ONU template fec function
Disable: Close the system ONU template fec function |
【 Example 】
|
Example1： enable system ONU template fec function
Enable/Disable system ONU template igmp fast-leave function
| Gommand Grammar | epon# system onu-template-config-system ctc igmp fast-leave
<state> |
| Function | enable/disable system ONU template igmp fast-leave function |
| <admin> | Enable: Open the system ONU template igmp fast-leave function
Disable: Close the system ONU template igmp fast-leave function |
【 Example 】
|
Example1： enable system ONU template igmp fast-leave function
configure system ONU template igmp mode
| Gommand Grammar | epon# system onu-template-config-system ctc igmp mode <mode> |
| Function | configure system ONU template igmp mode |
| <mode> | mode,{igmp-mld-snooping|controllable-igmp-mld|pass-through} |
【 Example 】
|
Example1： setting system ONU template igmp mode is igmp-mld-snooping
Enable/Disable system ONU template VOIP port
| Gommand Grammar | epon# system onu-template-config-system pots ctc admin
<admin> |
| Function | enable/disable system ONU template voip port |
| <admin> | Enable: Open the system ONU template VOIP port
Disable: Close the system ONU template VOIP port |
【 Example 】
Example1： enable the system ONU template voip port
Configure user ONU template
Enter user ONU template config mode
| Gommand Grammar | epon# system onu-template-config-user <templateID> |
| Function | Enter user onu template config mode |
| <templateID> | user onu template id :1-255 |
【 Example 】
|
Example1： enter user onu template config mode
configure user ONU template capacity
| Gommand Grammar | epon(onu_template-1)# config capacity <catvNum> <portNum>
<potsNum> <templateName> |
| Function | configure user ONU template capacity |
| <catvNum> | The number of catv port |
| <portNum> | The number of ethernet port |
| <potsNum> | The number of voip port |
| <templateName
> |
The name of template |
【 Example 】
Example1： setting user ONU template capacity is 1 CATV port 、 4 ethernet port and 1 VOIP
port and the name is template1
Enable/Disable user ONU template user port
| Gommand Grammar | epon(onu_template-1)# config uni <uniId> ctc admin <admin> |
| Function | enable/disable user ONU template user port |
| <uniId> | User port ID :<1-24> |
| <admin> | Enable: Open the user ONU template user port Disable: Close the user ONU template user port |
【 Example 】
|
Example1： enable the user ONU template user port
configure user ONU template egress-policing
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc engress-policing
<max-rate> |
| Function | configure system ONU template egress port rate |
| <uniId> | User port ID :<1-24> |
| <max-rate> | 0-1000000(kbps) |
configure user ONU template ingress-policing
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc ingress-policing
<max-rate> |
| Function | configure system ONU template ingress port rate |
| <uniId> | User port ID :<1-24> |
| <max-rate> | 0-1000000(kbps) |
Enable/Disable user ONU template auto negotiation function
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc auto-nego <admin> |
| Function | enable/disable user ONU template auto negotiate function |
| <uniId> | User port ID :<1-24> |
| <admin> | Enable: Open the user ONU template auto negotiate function Disable: Close the user ONU template auto negotiate function |
Enable/Disable user ONU template auto flow control function
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc flow-ctrl <admin> |
| Function | enable/disable user ONU template flow control function |
| <uniId> | User port ID :<1-24> |
| <admin> | Enable: Open the user ONU template flow control function Disable: Close the user ONU template flow control function |
Enable/Disable user ONU template auto loop-detec function
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc loop-detect <admin> |
| Function | enable/disable user ONU template loop detect function |
| <uniId> | User port ID :<1-24> |
| <admin> | Enable: Open the user ONU template loop detect function Disable: Close the user ONU template loop detect function |
configure user ONU template mac aging-time
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc mac-aging-time
<timer> |
| Function | configure user ONU template mac aging-time |
| <uniId> | User port ID :<1-24> |
| <timer> | Mac address aging time ：0-4294967295 second |
configure user ONU template statistics function
| Gommand Grammar | epon(onu_template-1)#config uni <uniId> ctc statistics
<monitoring-status> <monitoring-period> |
| Function | configure user ONU template mac aging-time |
| <uniId> | User port ID :<1-24> |
| <monitoring- status> | The status of statistics function Enable:open the statistics function Disable:close the statistics function |
| <monitoring- period> | The period of statistics:<1-4294967295> second |
- Switchcontrol card configuration
- Storm Control
Enable/Disable Storm Control and Configure the Storm Control Parameter
| Command Grammar | epon# swport <port> storm-ctrl <type> <enable> <rate> |
| Function | Enable or Disable Storm Control function and configure the storm control parameter |
| <type> | By now, support the follow： bcast-mcast-dlf,
broadcast multicast dlf broadcast-multicast broadcast-dlf multicast-dlf |
| <enable> | Enable: Open the storm control function Disable: Close the storm control funcion |
| <rate> | The control rate : 0-33554431(kbps) |
- Port manegemnet
enter switch port config mode
| Command Gtammar | epon#swport <port> |
| Function | enter switch port config mode. Noting: ge1-ge8 is eth port, ge9- ge16 is PON port |
| <port> | Switch port number ,<ge1-ge16> |
【 Example 】
Example 1 ： Enter Sithch port ge1 config mode
epon(GE–1)# ? Enter“ ？”show the current directory ：
admin – enable or disable current port admit-frame – set port access frame type auto-nego – enable auto-nego
def-pri – set port default priority
exit – exit current mode flow-ctrl – set port flow control
learning – configure switch port learning pvid – configure the PVID
rate-ctrl – configure rate-control
speed – configure the SPEED
storm-ctrl – Configurate storm control, support broadcast | mult icast | unknown unicast
vlan – add or del vlan list Global command:
logout – exit the CLI system
ping – test that a remote host is reachable
show – show system configuration
tracert – trace the route to host Port parameters
- Enable current port
| Command Grammar | epon(GE-1)# admin enable |
| Function | Configuration current port enable |
- Disable current port
| Command Grammar | epon(GE-1)# admin disable |
| Function | Disable current port |
- Set port access frame type
| Command Grammar | epon(GE-1)# admit-frame <type> |
| Function | set port access frame type |
| <type> | all：all of packet。
tagged ： only receive tag packet |
| untagged:only receive untag packet 。 |
- Set port default priority
| Command Grammar | epon(GE-1)# def-pri <priority> |
| Function | Configure the switch port default pvid, when switch port receive packet witch no tag, it will give the packet default pvid, that is the default 802.1p priority. |
| <priority> | Config priority ,valaue: <0-7> |
- Set port flow-ctrl function
| Command Grammar | epon(GE-1)# flow-ctrl <admin> |
| Funcion | Configurate storm control |
| <admin> | disable ： disable flow-ctrl function enable: enable flow-ctrl function |
Configurate the pvid of port
| Command Grammar | epon(GE-1)#pvid <pvid> |
| Function | Configurate the pvid of port |
| <pvid> | Optional parameters ：0-4094。 |
Configurate auto-nego of port
| Command Grammar | epon(GE-1)# auto-nego |
| Function | Configurate auto-nego of port |
Configurate the speed of port
| Command Grammar | epon(GE-1)#speed <speed> duplex <duplex> |
| Function | Configurate the speed of port |
| <speed> | Effective parameter;
<10m|100m|1000m> |
| <duplex> | Optional parameters
<full|half> |
Add vlan list of port
| Command Grammar | epon(GE-1)# vlan add <vidlist> <tag> |
| Function | Add vlan list port and set up tag mode |
| <vidlist> | vlan id list,<Combination of 1~4094> |
| <tag> | Mark way is optional parameters ，
Given tag parameters is out of the packet with the tag The tag parameter default is out of the packet without the tag |
【 Example 】
Example 1 ： create Vlan2-100 with the TAG TAG, create vlan101-200 without the TAG
markup under the exchange ge1 port
Delete the vlan list of port
| Command Grammar | epon(GE-1)# vlan delete <vidlist> |
| Function | Delete the vlan list of port |
| <vidlist> | vlan id list,<Combination of 1~4094> |
【 Example 】
Example 1 ： delete vlan 2-200 of ge1 port
Show swport current configuration information
| Command Grammar | epon# show swport ge1 attribute |
| Function | Show swport current configuration information |
【 Example 】
Example 1:show swport current configuration of ge1 port information
Configuration ingress-port rate
| Command Grammar | epon(GE-1)# rate-ctrl ingress <rate> |
| Function | Configuration ingress-port rate |
| <rate> | 0-1000000(kps) |
Configuration egress-port rate
| Command | epon(GE-1)# rate-ctrl egress <rate> |
| Grammar | |
| Function | Configuration engress-port rate |
| <rate> | 0-1000000(kps) |
- Configure switch mode
Show vlan state
| Command Grammar | epon#show swmode vlan |
| Function | Show vlan state |
【 Example 】
Example 1 ：show swmode vlan ：
Configure vlan enable/disable
| Command Grammar | epon# swmode vlan <mode> |
| Function | Enable/disable the vlan function |
| <mode> | Enable :enable vlan Disable :disable vlan |
- MAC address management
Configure mac-address aging timeout
| Command | epon# mac-address aging <timeout> |
| Grammar | |
| Function | Configure mac-address management timeout 。 |
| <timeout> | MAC aging time :range ：0-65535s |
Show mac-address aging
| Command Grammar | epon# show mac-address aging |
| Function | show mac-address-aging |
- Vlan Configuration management
Creat vlan
| Command Grammar | epon#vlan <vlanid> |
| Function | Creat vlan and enter vlan config mode |
| < vlanid > | 1-4094 |
【 Example 】
Example 1 ： Creat vlan100 and enter vlan100 config mode ，
epon(vlan–100) # ? enter“ ？” or “help” showwing the current directory ：
delete – delete vlan list
exit – exit current mode
member – add or delete member-port lobal command:
logout – exit the CLI system
ping – test that a remote host is reachable
show – show system configuration
tracert – trace the route to host
Add vlan port member
| Command Grammar | epon(vlan-100) # member add <member> <tag> |
| Function | add vlan member and set up tag |
| <member> | ge1-ge16 |
| <tag> | Mark way is optional parameters ，
Given tag parameters is out of the packet with the tag The tag parameter default is out of the packet without the tag |
【 Example 】
Example 1 ： add ge1,ge2 and ge3 as vlan100 member and set up tag ， add ge4 and ge5 as vlan100 member and set up untag：
Delete vlan port member
| Command Grammar | epon(vlan-100)# member del <member> |
| Function | Delete vlan port member 。 |
| <member> | ge1-ge16 。 |
Delete vlan
| Command Grammar | epon(vlan-100)#delete <vlanList> |
| Function | Delete vlan 。 |
| <vlanlistt> | Delete vlan list，Valid values :the combination of 1-4094， Example :
delete vlan 10,20,30 delete vlan 100-120 delete vlan 10,100-110,200 |
Show vlan configuration of vlan
| Command Grammar | epon#show vlan <vlanId> |
| Function | Show vlan configuration of vlan |
| <vlanId> | all： show all current vlan configuration 。
1-4094：show current vlan-id configration 。 |
【 Example 】
Example 1 ： show all currnet vlan configuration ：
Rstp configuration management
Enable/disable RSTP configuration
| Command Grammar | epon# rstp <state> |
|
Function |
Enable/disable RSTP Function |
| <state> | enable:enable Rstp Function disable:disable Rstp Function |
【 Example 】
Example 1 ： enable Rstp function
epon# rstp enable Enable RSTP successful!
|
Example 2 ： disable Rstp function
Configure Rstp bridge maxage aging time
| Command Grammar | epon# rstp bridge maxage <aging> |
| Function | Configure Rstp bridge maxage aging time |
| <aging> | Range: 6-40
Bridge Max Age must be less than or equal to twice the the Bri dge Forwarding Delay minus 1. |
【 Example 】
|
Example 1 ： if the forward delay is a maximum of 15 s, configuring the biggest aging time is 28s
Configure Rstp bridge delay time
| Command Grammar | epon# rstp bridge fdelay <fdelay> |
| Function | Configure Rstp bridge fdelay time |
| <fdelay> | Range: 4-30s |
【 Example 】
Example 1:configuring Rstp bridge delay time is 15s
Configure Rstp bridge prioprity
| Command Grammar | epon# rstp bridge priority <prio> |
| Function | Configure Rstp bridge prioprity |
| <prio> | Range:p0-p65535 |
【 Example 】
|
example1： setting Rstp bridge priority is 0
Configure max counts of Rstp packet per second
| Command Grammar | epon# rstp hold-count <count> |
| Function | Configure max counts of Rstp packet per second |
| <count> | Range:1-10 |
【 Example 】
|
Example 1 ： Configure transmit 10 hold-counts of Rstp per second
Configure Rstp port piority
| Commad Grammar | epon# rstp port <protid> priority <prio> |
| Function | Configure Rstp port priority |
| <protid> | Range ； ge1-ge16 |
| <prio> | Value :p0,p16,p32,p48,p64,p80,p96,p112,p128,p144,p160,p17 6,p192,p208,p224,p240 |
【 Example 】
|
Example 1 ： setting ge1 port priority is 0
Configure Rstp port path-cost
| Command Grammar | epon# rstp port <protid> path-cost <pathcost> |
| Function | Configure Rstp port path-cost |
| <protid> | Port |
| <pathcost> | Port path cost |
【 Example 】
|
Example 1 ： setting ge1 path-cost of Rstp is 2000
Configure Rstp edge-port
| Command Grammar | epon# rstp port <protid> edgecfg <edge> |
| Function | Configure Rstp edge-port |
| <protid> | Switch port |
| <edge> | edge: edge
none-edge:none edge auto： Automatic negotiation Note: the edge of the port don’t need after discarding – learning – forwarding steps, and direct conversion to the forwarding state, the rest of the ports need to pass the above process |
【 Example 】
Example 1 ： setting ge1 is edge of Rstp
Example 2 ： setting ge1 is auto configuration
Configure Rstp p2p port
| Command Grammar | epon#rstp port <protid> p2pcfg <p2p> |
| Function | Configure Rstp p2p port |
| <protid> | Switch port |
| <p2p> | Shared
p2p :p2p port auto： Automatic negotiation Note: p2p port to allow rapid transition to the forwarding state, shard port need through discarding – learning – forwarding steps forward to transition to the state |
【 Example 】
|
Example ： setting ge1 port is p2p port
Configure Rstp protocol version check
| Command Grammar | epon#rstp port <protid> p2pcfg mcheck |
| Function | Configure Rstp protocol version checlk |
| <protid> | Switch port |
【 Example 】
Example:1 Configure Rstp protocol version check
Show Rstp information
| Command Grammar | epon#show rstp <protid> |
| Function | Show Rstp information |
| <protid> | Switch port |
【 Example 】
Example 1 ： show Rstp information
Trunk configuration managemnet
Enter trunk config mode
| Command | epon# trunk <tid> |
| Grammar | |
| Function | Enter trunk config mode |
| <tid> | Range:1-4 |
【 Example 】
|
Example 1 ：enter trunk 1 config mode view
Add port of trunk member
| Command Grammar | epon(trunk-1)# member add <member> |
| Function | Add trunk’s member |
| <member> | Porttlist |
【 Example 】
Example 1 :add ge1-ge2 port of trunk 1 member
Delete port of trunk member
| Command Grammar | epon(trunk-1)# member del <member> |
| Function | Delete port of trunk member |
| <member> | Portlist |
【 Example 】
|
Example1： delete ge1-ge2 of trunk 1 member
Delete trunklist configuraion
| Command Grammar | epon(trunk-1)# delete <trunkList> |
| Function | Delete trunklist configuration |
| <trunklist> | Range: 1-4 |
【 Example 】
|
Example1 ： delete list 1-2 configuration of trunklist
Show trunk information
| Command Grammar | epon# show trunk <trunkid> |
| Function | Show trunk information |
| <trunkid> | all： all of trunklist 。
1-4 ： Specify the trunk group information |
【 Example 】
|
Example 1 ：show all trunklist information
Rmon network monitoring and configuration
- clear all ports statistics
| Command Grammar | epon# rmon statistics clear-all |
| Function | Clear all ports statistics |
- Delete the specified port configuration information
| Command Grammar | epon# rmon statistics clear <port> |
| Function | Delete the specified port configuration information |
| <port> | Interface, refer to above 2.3 |
【 Example 】
|
Example1 ： Delete the statistics RMON statistics from the GE1 interface
rmon history configration
- Add rmon history configration
| Command Grammar | epon# rmon history add <port> <entry-number> <buckets- number> <interval> <owner> |
| Function | Rmon history configration |
| <port> | Switch port |
| <entry-number> | History index ，range:1-65535 |
| <buckets- number> | History Record number ，range 1-65535 |
| <interval> | The time interval of history |
| <owner> | Belongs to user |
【 Example 】
Example 1 ： configue ge1 port rmon ‘s index is 1 ，inteval is 5 ,buckets-number is 5, owner is
user1
- Delete rmon history configuration
| Command Grammar | epon# rmon history del < entry-number> |
| Function | Delete rmon history configuration |
| <entry-number> | History infdex,range:1-65535 |
rmon event configuration
- add rmon event configuration
| Command Grammar | epon#rmon event add <entry-number> <description> <type>
<owner> |
| Function | Add rmon event configuration |
| <entry-number> | Event index ， range ： 1-65535 |
| <description> | Description information |
| <type> | none ； no log and no trap
log ：Record the log information trap ： Record the trap information log-trap:Record the log and trap information |
| <owner > | Belongs to user |
【 Example 】
|
Example 1 ： add rmon event 100
1 delete rmon event
| Command | epon#rmon event del <entry-number> |
| Grammar | |
| Function | Delete rmon event |
| <entry-number> | Range:1-65535 |
【 Example 】
|
Example 1 ： delete rmon event 100
rmon alarm configuration
add rmon alarm configuration
| Command Grammar | epon#rmon alarm add <entry-number> <alarm-variable>
<interval> <type> <rising-value> <rising-event> <falling-value> <falling-event> <owner> |
| Function | Add rmon alarm |
| <entry-number> | Range:1-65535 |
| <alarm-variable> | Oid ,snmp oid |
| <interval> | Sampling interval |
| <type > | delta: Refers to two time interval only
absolute: Refers to achieve value within a specified period |
| <rising-value> | Range:2147483648 – +2147483647 |
| <rising-event> | Rising event |
| <falling-value> | range ： 2147483648 – +2147483647 |
| <falling-event> | Falling event |
| <Owner> | owner |
【 Example 】
Example 1 ： add alarm comfiguration that oid is 1.3.6.1.2.1.16.1.1.1.4.1 ,interval 5s rising- value 40000 ， Rissing-event is 1 ， falling-event 20000 ， falling-event is 1 ,type is
absolute
Delete rmon alarm configuration
| Command Grammar | epon#rmon alarm del<entry-number> |
| Function | Delete rmon alarm configuration |
| <entry-number> | Event index ，range:1-65535 |
【 Example 】
Example1 ： delete rmon alarm 1
Show rmon statistics information
| Command Grammar | epon# show rmon statistics <port> |
| Function | Show rmon port statistics information |
| <port> | Device port |
【 Example 】
Example 1 ：show rmon statistics ge1
Show rmon history information
| Command Grammar | epon# show rmon history <port> |
| Function | Show rmon history information about port |
| <port> | Switch port |
【 Example 】
Example 1 ： show rmom history ge1
show rmon event information
| Command Grammar | epon# show rmon event <entry-number> |
| Function | Show rmon event information |
| <entry-number> | Event entry-number ， 0 means all of event |
【 Example 】
|
Example 1 ：show rmon event 1 information
Show rmon eventlog information
| Command Grammar | epon# show rmon eventlog <entry-number> |
| Function | Show rmon eventlog information |
| <entry-number> | Event entry-number ,0 means all of eventlog |
【 Example 】
|
Example 1 ： show rmon eventlog 1
Show rmon alarm information
| Command Grammar | epon#show rmon alarm <entry-number> |
| Function | Show rmon alarm information |
| <entry-number> | Alarm entry-number, 0 means all of alarm |
【 Example 】
|
Example 1 ： show all of alarm of rmon information
Mirror port configuration management
Enable/disable mirror fuction
| Command Grammar | epon# mirror admin <admin> |
| Function | Enable/disable mirror function 。 |
| <admin> | enable:enable mirror fuction disable: disable mirror fuction |
【 Example 】
Example 1 ： enable mirror function
Example 2 ： disable mirror function
Configure mirror source_port
| Command Grammar | epon# mirror source_port <port> <type> |
| Function | Configure mirror source_port |
| <port> | Switch port |
| <type> | none: soure_port have no set egress: the packet of out_flow ingress: the packet of in_flow
full ： packet both of out_flow and in_flow |
【 Example 】
Example 1 ：configure ge1 ingress mirror
Example 2 ：configure soure_port ge2 egress mirror
Example 3 ， configure ge3 both of out_packet and in_packet
Configure mirror dest_port
| Command Grammar | epon# mirror dest_port <port> |
| Function | Configure mirror dest_port |
| <port> | Switch port |
【 Example 】
|
Example 1 ： configure dest_port ge8
Show mirror information
| Command Grammar | epon# show mirror |
| Function | Show mirror information |
【 Example 】
|
Example 1 ：show mirror information
Igmp-snooping monitoring and configuration
Enable/disable igmp snooping function
| Command Grammar | epon# igmp-snooping admin <admin> |
| Function | Enable/disable igmp snooping function |
| <admin> | <disable|enable> |
Enable/disable igmp snooping fast-leave function
| Command Grammar | epon# igmp-snooping fast-leave <admin> |
| Function | Enable/disable the igmp snooping fast-leave function |
| <admin> | <disable|enable> |
Enable/disable igmp snooping drop-unknown function
| Command Grammar | epon# igmp-snooping drop-unknown <admin> |
| Function | Enable/disable the igmp snooping drop-unknown function |
| <admin> | <disable|enable> |
Configure igmp snooping host-aging-time
| Command Grammar | epon# igmp-snooping host-aging-time <aging> |
| Function | configure IGMP Snooping host aging time |
| <aging> | Aging time:<1~3000>s |
Enable/disable igmp snooping querier function
| Command Grammar | epon# igmp-snooping querier <admin> |
| Function | Enable/disable the igmp snooping querier function |
| <admin> | <disable|enable> |
Configure igmp snooping querier query interval
| Command Grammar | epon# igmp-snooping querier interval <time> |
| Function | configure igmp query interval |
| <time> | Query interval： <2~3000>S |
Configure igmp snooping querier max-response-time
| Command Grammar | epon# igmp-snooping querier max-response-time <time> |
| Function | configure igmp query max rsp time |
| <time> | Query interval： <1~25>S |
Configure igmp snooping querier source_ip
| Command Grammar | epon# igmp-snooping querier source_ip <source_ip> |
| Function | configure igmp query source ip |
| <source_ip> | <X.X.X.X> |
Configure igmp snooping querier router-aging-time
| Command Grammar | epon# igmp-snooping router-aging-time <aging> |
| Function | configure IGMP Snooping router aging time |
| <aging> | <1~3000>S |
add/delet igmp-snooping static port
| Command Grammar | epon# igmp-snooping static <operation> <multicast_ip> <vlan>
<port> |
| Function | add or delete static igmp port |
| <operation> | operation, <add|del> |
| <multicast_ip> | multicast ip address, <x.x.x.x> |
| <vlan> | vlan id, <1~4095> |
| <port> | port, <ge1-ge8, pon1-pon8> |
clear all learned mac address
| Command Grammar | epon#reset mac-address-table |
| Function | clear all learned mac address |
- OLTManagement
- OLT basic configure management
Enter OLT Management
| Command Grammar | epon#olt <oltID> |
| Function | Enter olt configure mode |
| <oltID> | Pon ID : 1-8。 |
【 Example 】
|
Example 1 ： enter olt’s first pon configure mode ：
epon(olt-1)# ？
acl – configure olt level acl
admin – enable or disable this PON
alarm – enable or disable the message of Alarm! exit – exit current mode
mac-address-table – configure mac-address-table offline-onu – add or delete offline onu
onu – configure onu
optical – olt optical diagnose
p2p – configure p2p
packet-filter – enable or disable packet filter qinq – configure QinQ
tpid – configure olt default tpid Global command:
logout – exit the CLI system
ping – test that a remote host is reachable
show – show system configuration
tracert – trace the route to host
Enable/disable OLT port
| Command Grammar | epon(olt-1)#admin <enable | disable> |
| Function | enable/disabke OLT PON port. Default status is enable. |
| <eable> | Enbale OLT PON port 1 。 |
| <disable> | Disable OLT PON port 1 。 |
Long light checking Function
Configuration all of onu about long light checking Function
| Command Grammar | epon(olt-1)# optical lao |
| Function | ON optical tests under all the ONU, ONU luminous fault to kick off |
Configure the specified onu about long checking fuction
| Command Grammar | epon(olt-1)# optical lol <llid_1> <llid_2> <llid_3> |
| Function | Light tests specified under the PON ONU, luminous fault to kick off |
Configure p2p Function
| Command Grammar | epon(olt-1)# p2p <enable | disable> |
| Function | Enabel/disable OLT P2P function, when enable this function,each onu register to this pon can reach each other without uplink swicht |
| <eable> | Enabel P2P |
| <disable> | Disable P2P |
Configure out-tpid Function
| Command Grammar | epon(olt-1)# tpid out-tpid <tpid> |
| Function | Configure acl default tpid |
| <tpid> | 0x8100, 0x9100, 0x88a8 |
- OLT ACL Configure
Delete One ACL
| Command Grammar | epon(olt-1)# acl <aclId> delete |
| Function | Delete the aclid’s acl |
| <aclId> | Acl id number : <1-30> |
【 Example 】
|
Example 1 ：delege olt 1 acl 1：
Delete Current OLT All ACL
| Command Grammar | epon(olt-1)#acl delete |
| Function | Delete current olt’s all acl |
【 Example 】
|
Example 1 ： delete olt1’s all acl ：
Add OLT ACL
| Command Grammar | epon(olt-1)#acl <aclId> rule <direction> <precedence> matching “matching string” action “action string” | |
| Function | Add one acl in current olt | |
| <aclId> | value ：<1-40> | |
| <direction> | Acl direction ： <upstream|downstream> | |
| <precedence> | Acl priority ： <4-7> | |
| matching string | String to match, fomat is ：”proto=12 dst-port=34″. Support the parameters as blow: [dst-mac|src-mac] <xx:xx:xx:xx:xx:xx> [tag-num] <0|1|2|more> [top-vid|inner-vid] <vid|vidL-vidH>, vid:1~4094 [top-8021p|inner-8021p] <8021p|8021pL-8021pH>, 8021p:0~7 [eth-type] <0~65535> [dscp] <0~63> [proto] <0~65535> [dst-ip|src-ip] <x.x.x.x> [dst-port|src-port] <0~65535> | |
| action string | Acton string, format as “8021p 7 dscp 63”.
Support the parameters as blow ： [cos] <0~7> [8021p] <0~7> [dscp] <0~63> [fwd] <deny> [rate] cir <> cbs <> pir <> pbs <> [top-vlan | inner-vlan] <pop | push vid <1~4094> | swap vid <1~4094> |
|
【 Example 】
Example 1 ： Filtering the upstream frame of destination MAC address is 00:00:00:00:00:02
Example 2 ： Filtering the downstream of destination MAC address is 00:00:00:00:00:01, tagged is with external VLAN 4094：
Example 3 ： Filtering the upstream frame with vlan 100, tagged it with external VLAN 200 ：
Example 4 ： Filtering the upstream frame of destination IP address is 198.19.1.2, tagged it with external vlan 1000 ：
Example 5 ： Filtering the upstream frame of destionation port is port-2, tagged it with external vlan 1000 ：
OLT MAC Management
Configure OLT MACAge Time
| Command Grammar | epon(olt-1)# mac-address-table aging-time <aging-time> |
| Function | Configure current olt’s mac age time |
| <aging-time> | Age time: <0~65535> sec, when configure age time to 0, the mac will not ageout |
【 Example 】
|
Example 1 ：configure current olt’s age time to 200s：
Flush current olt’s mac table list
| Command Grammar | epon(olt-1)# mac-address-table flush |
| Function | Flush current olt’s mac table list |
Enable OLT MAC Learening function
| Command Grammar | epon(olt-1)# mac-address-table learning enable |
| Function | Enable current olt’s mac learning function |
Disable OLT MAC Learning Function
| Command Grammar | epon(olt-1)# mac-address-table learning disable |
| Function | Disable current olt’s mac learning function |
Enable MAC Move
| Command Grammar | epon(olt-1)# mac-address-table move enable |
| Function | Enable mac move |
Disable MAC Move
| Command Grammar | epon(olt-1)# mac-address-table move disable |
| Function | Disable mac move |
- OLT Auth
Disable OLT Auth
| Command Grammar | epon# auth disable |
| Function | Disable auth function, when the olt auth is disable, onu will register |
| automatically. |
Add/Delete/Show Whitelist
Add white member
| Command Grammar | epon# auth whitelist add <oltID> onu <onu> |
| Function | Add white member. It will enable the Auth function when first add black member |
| <oltID> | Pon ID : 1-8 |
| <onu> | ONU-MAC ， format： 00-01-02-AB-CD-EF |
|
Example 1 ： add oun witch MAC 00-1b-62-48-5b-09 to whitelist ：
Delete white member
| Command Grammar | epon# auth whitelist delete <oltID> <onu> |
| Function | Delete white member |
| <oltID> | Pon ID : 1-8 |
| <onu> | ONU-MAC ， format： 00-01-02-AB-CD-EF。 |
【 Example 】
|
Example 1 ： move onu with MAC 00-1b-62-48-5b-09 out from whitelist ：
Show whitelist
| Command Grammar | epon# show auth whitelist |
| Function | Show whitelist |
【 Example 】
|
Example 1 ：show whitelist：
Add/Delete/Show Blacklist
Add black member
| Command Grammar | epon# auth blacklist add <oltID> onu <onu> |
| Function | Add black member. It will enable the Auth function when first add black member |
| <oltID> | Pon ID : 1-8 |
| <onu> | ONU-MAC ， format： 00-01-02-AB-CD-EF。 |
【 Example 】
|
Example 1 ： add a black member that mac is 00-1b-62-48-5b-09 ：
Delete Black Member
| Command Grammar | epon# auth blacklist delete <oltID> onu <onu> |
| Function | Delete black member |
| <oltID> | Pon ID : 1-8 |
| <onu> | ONU-MAC ， format： 00-01-02-AB-CD-EF |
【 Example 】
|
Example 1 ： move onu with MAC 00-1b-62-48-5b-09 out from blacklist ：
Show blacklist
| Command Grammar | epon# show auth blacklist | |
| Function | Show blacklist | |
【 Example 】
|
Example 1 ： show blacklist ：
OLT hybrid Auth Mode Configure
Enable hybrid auth mode
| Command Grammar | epon# auth ctc-mode hybrid |
| Function | enable hybrid auth mode |
【 Example 】
|
Example 1 ：enable hybrd auth mode：
OLT LOID Auth Mode Configure
Enable loid auth mode
| Command Grammar | epon# auth ctc-mode loid |
| Function | enable LOID auth mode |
【 Example 】
Example 1 ： enable loid auth mode
Add loid account
| Command Grammar | epon# auth ctc-mode add-loid <loid> password <password> |
| Function | Add LOID account |
| <loid> | {MAX 24 Chars} |
| <password> | {MAX 12 Chars} |
【 Example 】
|
Example 1 ：add one loid account, name: cdt, password:cdt：
Delete loid account
| Command Grammar | epon# auth ctc-mode delete-loid <loid> password <password> |
| Function | Delete LOID account |
| <loid> | {MAX 24 Chars} |
| <password> | {MAX 12 Chars} |
【 Example 】
|
Example 1 ： delete a loid account ：
OLT MAC Auth Mode Configure
| Command Grammar | epon# auth ctc-mode mac |
| Function | Enable OLT MAC Auth Mode |
- Configure packet_filter of OLT PON port
Packet_filter of OLT PON port about DHCP function
| Command Grammar | epon(olt-1)# packet-filter dhcp <admin> |
| Function | Filter upstream flow about dhcp servers packet |
| <admin> | enable:enable packet-filter dhcp disable ： disable packet-filter dhcp |
【 Example 】
|
Example 1 ：enable dhcp packet_fil ter function of olt
EOC MME packet-filter function
| Command Grammar | epon(olt-1)# packet-filter eoc_mme <admin> |
| Function | EOC MME packet filter |
| <admin> | enable:enable eoc_mme function disable ： disable eoc_mme function |
【 Example 】
|
Example 1 ： enable eoc_mme packet-filter function
Netbios packet-filter function
| Command Grammar | epon(olt-1)# packet-filter netbios <admin> |
| Function | netbios packet filter |
| <admin> | enable:enable netbios function disable ： disable netbios function |
【 Example 】
|
Example 1 ： enable netbios packet-filter function
8306_rtk_loopback packet-filter function
| Command Grammar | epon(olt-1)# packet-filter 8306_rtk_loopback <admin> |
| Function | 8306_rtk_loopback packet filter |
| <admin> | enable:enable 8306_rtk_loopback function disable ： disable 8306_rtk_loopback function |
【 Example 】
|
Example 1 ： enable 8306_rtk_loopback packet-filter function
Configure trap alarm and message alarm function of ONU
Configure message alarm about ONU off the electricity
| Command Grammar | epon(olt-1)# alarm onuDyingGasp <admin> |
| Function | ONU off the electricity ,it can print GASP message on the console |
| <admin> | enable: enable message fuction 。
disable ： disable message function 。 |
【 Example 】
Example 1 ： Configure GASP message function ， ONU off the electricity ,it can print GASP message on the
console
Configure trap alarm about ONU off the electricity
| Command Grammar | epon(olt-1)# alarm onuDyingGaspTrap <admin> |
| Function | ONU off the electricity,it can send trap message about GASP |
| <admin> | enable:enable send trap of onu Dying Gasp! disable ：disable send trap of onu Dying Gasp!。 |
【 Example 】
Example 1 ： after ONU off the electricit ， TRAP alarm will be sended to SNMP management
software
Configure QinQ function
Add QinQ configuration
| Command Grammar | epon(olt-1)# qinq enable <qinq-vid> raw-vlan-id-inbound <vlan- list> |
| Function | Configure QinQ function |
| <qinq-vid> | Outbound vlan |
| <vlan-list> | inbound vlan list |
【 Example 】
Example 1 ： setting QinQ configuration that inbound vlan_list is 50-90 and setting outbound
vlan is 100
Delete QinQ configuration
| Command Grammar | epon(olt-1)# qinq disable <qinq-vid> |
| Function | delete QinQ f configuration |
| <qinq-vid> | Outbond vlan |
【 Example 】
|
Example 1 ： delete QinQ configuration that and setting outbound vlan is 100
Configure offline ONU
Add offline ONU and bind the template with ONU
| Command Grammar | epon#offline-onu add <onuID> <onuMAC> <templateID> |
| Function | Add offline ONU and bind the template with ONU. Template just can only bind the offline ONU that no-bind with any template before. If offline ONU have binded template before, you need to delet the template. |
| <onuID> | onuID will be used when ONU online |
| <onuMAC> | ONU mac address |
| <templateID> | When ONU online in the first time, OLT will set the ONU configuration by template |
delete offline ONU
| Command Grammar | epon(olt-1)# offline-onu del <onuID> |
| Function | delete offline ONU. It must to delete offline ONU in OLT list before binding a new template with ONU |
| <onuID> | Outbond vlan |
- Show olt configuration information
Show olt attribute information
| Command Grammar | epon#show olt <oltID> attribute | |
| Function | Show olt attribute information | |
| <oltID> | Pon port ID ，range:1-8。 | |
【 Example 】
|
Example1： show olt attribute information ：
| Command Grammar | epon#show olt <oltID> optical |
| Function | Show olt optical information 。 |
| <oltID> | Pon port ID ，range:1-8 |
【 Example 】
Example1： show olt optical information
Show olt online-onu information
| Command Grammar | epon#show olt <oltID> online-onu |
| Function | Show olt online-onu information 。 |
| <oltID> | Pon port ID ，range:1-8。 |
【 Example 】
|
|||||||||||||||||||||
Example1： show olt online-onu information ：
Show olt acl information
| Command Grammar | epon#show olt <oltID> acl |
| Function | Show olt acl information。 |
| <oltID> | Pon port ID ，range:1-8。 |
【 Example 】
|
Example1：show olt acl information：
Show olt auth mode information
| Command | epon# show auth mode |
| Grammar | |
| Function | Show olt auth mode information |
【 Example 】
|
Example1： show olt auth mode information ：
Show olt port staus information
| Command Grammar | epon(olt-1)# show olt <oltId>admin |
| Function | Show olt port staus information |
| <oltId> | Pon port ID ，range:1-8 |
【 Example 】
Example1:show olt port staus
Show olt alarm information
| Command Grammar | epon(olt-1)# show olt <oltId> alarm |
| Function | Show olt alarm information |
| <oltId> | Pon port ID ，range:1-8。 |
【 Example 】
|
Example1： show olt ararm information
Show olt learning-mac information
| Command Grammar | epon(olt-1)# show olt <oltId> mac-address-table < onu> |
| Function | Show olt learning-mac information |
| <oltId> | Pon port ID ，range:1-8。 |
| <onu> | Don’t pick up parameters:show mac address of all port
With parameters :show mac address of specified port |
【 Example 】
|
Example1：show mac address of all port 。
Show olt p2p information
| Command Grammar | epon# show olt <oltId> p2p |
| Function | Pon port ID ，range:1-8。 |
| <oltId> | Pon port ID ，range:1-8。。 |
【 Example 】
|
Example1 ： show olt p2p information
Show olt packet-filter information
| Command Grammar | epon# show olt <oltId> packet-filter <type> |
| Function | Show olt packet-filter information |
| <oltId> | Pon port ID ，range:1-8。 |
【 Example 】
|
Example1： show olt packet-filter information
Show olt tpid out-tpid
| Command Grammar | epon#show olt <oltid> tpid out-tpid |
| Function | Show olt tpid out-tpid |
| <oltId> | Pon port ID ，range:1-8。 |
- ONU Management
- Show ONU Basic Information
Show Online ONU
| Command Grammar | epon# show olt 7 online-onu |
| Function | Use this command in any mode can check to the specified PON port of the Online-ONU. |
【 Example 】
|
||||||||||||||||||||||||||
Example1： show online-onu
Show ONU Version
| Command Grammar | epon# show olt 7 onu <onuid> ctc sn |
| Function | Show online-onu version. |
| <onuid> | Designate online-onu onuid with value range from 1-64. |
【 Example 】
|
Example1： show onu version
Show ONU Capabilities
| Command Grammar | epon# show olt 7 onu <onuid> ctc capabilities |
| Function | Show online-onu capabilities. |
| <onuid> | Designate online-onu onuid with value range from 1-64. |
Show ONU Optical
| Command Grammar | epon# show olt 7 onu <onuid> ctc optical |
| Function | Show online-onu optical. |
| <onuid> | Designate online-onu onuid with value range from 1-64. |
- ONU Management Mode
| Command Grammar | epon(olt-7)#onu <onuid> |
| Function | enter ONU management mode to configure ONU. |
| <onuid> | designate onuid with valid value 1-64. |
【 Example 】
|
Example1：enter onu 1 managemnet mode：
epon(olt-7/onu-1)# input ”?” to show the following directory:
catv – enable or disable CATV
ctc – CTC configuration mode
default – restore to default setting
deregister – deregister current onu exit – exit current mode
info – onu device user information
link – enter link configure mode
pon – configure onu PON
pots – configure VOIP port
protect – enable or disable to isolate the uni(s) save – save current ONU configuration
uni – configure UNI Global command:
logout – exit the CLI system
ping – test that a remote host is reachable
show – show system configuration
tracert – trace the route to host
- ONU Basic Operation and Management
Reboot ONU
| Command Grammar | epon(olt-7/onu-1)# ctc reboot |
| Function | reboot ONU. |
Deregister ONU
| Command Grammar | epon(olt-7/onu-1)# deregister |
| Function | deregister ONU. |
Configure ONU FEC
| Command Grammar | epon(olt-7/onu-1)# ctc fec <oper> |
| Function | Configure ONU fec. |
| <oper> | value <enable/disable>
enable： enable ONU FEC function disable ： disable ONU FEC function |
Restore ONU to Default Settings
| Command Grammar | epon(olt-7/onu-1)#default |
| Function | restore ONU to default settings. |
【 Notes 】
This command will delete all configuration of the ONU, restored to the factory default configuration, and will automatically restart ONU.
Configure ONU Sys Management IP
| Command Grammar | epon(olt-2/onu-4)#ctc mng-ip <ip> <netmask> <gateway>
<CVLAN> <SVLAN> |
| Function | configure onu sys management ip. |
| Parameters | <ip> – example: 192.168.12.122 |
| <netmask> – example: 255.255.255.0
<gateway> – example: 192.168.0.1 <CVLAN> – 0-4094 <SVLAN> – 0-4094 |
Save Current ONU Configuration
| Command Grammar | epon(olt-7/onu-1)# save |
| Function | Save current onu configuration. |
upgrade ONU software
| Command Grammar | epon(olt-7/onu-1)# ctc upgrade <tftp-server> <image-file> |
| Function | Upgrade ONU software versions |
| <tftp-server> | Tftp server Ip |
| <image-file> | File name |
- Configure ONU IGMP
ONU IGMP Global Configuration
clear-all-multicast-ctrl-group
| Command Grammar | epon(olt-7/onu-1)# ctc igmp clear-all-multicast-ctrl-group |
| Function | clear all multicast ctrl group. |
Configure ONU IGMP fast-leave
| Command Grammar | epon(olt-7/onu-1)# ctc igmp fast-leave <oper> |
| Function | Configure ONU igmp fast-leave function. |
| <oper> | value <enable/disable> enable： enable igmp fast-leave
disable ： disable igmp fast-leave |
Configure ONU IGMP Mode
| Command Grammar | epon(olt-7/onu-1)#ctc igmp mode < mode > |
| Function | configure ONU igmp mode. |
| <mode> | valid value ： < gmp-mld-snooping controllable-igmp-mld igmp- snooping-only controllable-igmp pass-through> Some of the
parameters may not support, the default is gmp-mld-snooping. |
Configure ONU UNI Port IGMP
configure igmp group
| Command Grammar | epon(olt-5/onu-7/uni-1)# ctc igmp max-group <groups> |
| Function | configure igmp group. |
| <groups> | designate number of igmp groups with valid value <0-255>. |
Configure igmp vlan
| Command Grammar | epon(olt-5/onu-7/uni-1)# ctc igmp vlan-list < vlanTagList> |
| Function | configure igmp vlan. |
| <vlanTagList> | valid value ：1-4094， or null |
Configure vlan tag
| Command Grammar | epon(olt-5/onu-7/uni-1)# ctc igmp tag-handle <oper> |
| Function | configure igmp vlan tag or untag. |
| < Parameters > | value ：not-strip-vlan-tag strip-vlan-tag
switch |
- Enter ONU Link Mode
enter ONU link mode
| Command Grammar | epon(olt-7/onu-1)#link <linkID> |
| Function | enter ONU link mode. |
| <linkID> | valid value ： <1-8> |
Configure ONU Link Upstream SLA
| Command Grammar | epon(olt-7/onu-1/link-1)# sla upstream <fix> <cir> <pir> <weight> |
| Function | configure ONU LINK upstream speed limit. |
| <fix> | valid value ： <0~950000>Kbps |
| <cir> | valid value ： <1~950000>Kbps |
| <pir> | valid value ： <512~1000000>Kbps |
| <weight> | valid value ： <1~20> |
Configure ONU Link Downstream SLA
| Command Grammar | epon(olt-7/onu-1/link-1)# sla downstream <pir> <burst>
<weight> |
| Function | configure ONU LINK downstream speed limit. |
| <pir> | valid value ： <512~1000000>Kbps |
| <burst> | valid value ： <128~16383>*256Byte |
| <weight> | valid value ： <0~15> |
Configure ONU Link Acl
| Command Grammar | epon(olt-7/onu-1/link-1)#acl <Aclid> rule <direction>
<precedence> matching <matching string> action <action string> |
| Function | configure ONU link acl rule. |
| <aclid> | valid value ： 1-8 |
| <direction> | parameters ： upstream downstream |
| <precedence | valid value ： <4-7> |
| <matching string> | parameters ： [dst-mac] <xx:xx:xx:xx:xx:xx>. [src-mac] <xx:xx:xx:xx:xx:xx>. [tag-num] <0 | 1 | 2 | more>. [top-vid] <vid | vidL-vidH>, vid:1~4094. [inner-vid] <vid | vidL-vidH>, vid:1~4094. [top-8021p] <8021p | 8021pL-8021pH>, 8021p:0~7. [inner-8021p] <8021p | 8021pL-8021pH>, 8021p:0~7. [eth-type] <0~65535>. [dscp] <0~63>. [proto] <0~65535>. [dst-ip] <x.x.x.x>. [src-ip] <x.x.x.x>. [dst-port] <0~65535>. [src-port] <0~65535>. |
| <actionstring> | parameters ：
[cos] <0~7>. [8021p] <0~7>.
[dscp] <0~63>. [fwd] deny.
[rate] cir <cir> cbs <cbs> pir <pir> pbs <pbs>,
cir, pir: <0~1000000>Kpbs. cbs, pbs: <0~4095>KB [top-vlan] pop. [top-vlan] push vid <1~4094>. [top-vlan] swap vid <1~4094>. [inner-vlan] pop. [inner-vlan] push vid <1~4094>. [inner-vlan] swap vid <1~4094>. |
【 Example 】
|
Example1： configure ONU link acl 1 rule
enable/disable ONU port isolate function
| Command Grammar | epon(olt-7/onu-1)# protect <admin> |
| Function | Enable/disable ONU port isolate function. |
| < admin> | <enable | disable> |
- Configure ONU pon statistics
| Command Grammar | epon(olt-7/onu-1)# pon ctc statistics <monitoring-status>
<monitoring-period> |
| Function | Configure ONU pon statistics |
| < monitoring- status> | <disable | enable> |
| < monitoring- period> | 1-4294967295 second |
- Enable/disable ONU CATV port
| Command Grammar | epon(olt-7/onu-1)# catv <state> |
| Function | Enable/disable ONU CATV port |
| < admin> | <enable | disable> |
- Enter ONU Uni Port Management Mode
| Command Grammar | epon(olt-7/onu-1)# uni <uni> |
| Function | enter the ONU uniport management mode to configure the ONU uni parameter. |
| < uni> | designate ONU uni port with valid value <1-24>. |
【 Example 】
|
Example1： enter the ONU uni port 1 management mode ：
epon(olt-7/onu-1/uni-1)# ？ input ”?” to show the following directory:
ctc – ctc management mode exit – exit current mode
Global command: debug – debug
disable – entry guest level
logout – exit the CLI system
show – show system configuration Configure ONU Uni Port Parameters
Show ONU Uni port information
| Command Gramma | epon(olt-7/onu-1/uni-1)# show olt 7 onu 1 uni 1 ctc attribute |
| Function | Using the command in any mode,can display the current ONU uni port parameter properties. |
【 Example 】
|
Example1： show ONU uni port 1 information ：
configure ONU Uni port storm control
| Command Gramma | epon(olt-7/onu-1/uni-1)# storm-ctrl <type> <admin> <rate> |
| Function | Configure ONU Uni port storm control |
| <type> | <none|broadcast|multicast|broadcast-multicast|unknown-uc| broadcast-unknown-uc|multicast-unknown-uc|bc-mc-unknown- uc> |
| <admin> | <enable|disable> |
| <rate> | [0-16777215], unit(bps) |
enable or disable ONU Uni port
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc admin <oper> |
| Function | enable or disable ONU current port |
| <oper> | value <enable | disable>： enable ：enable ONU port disable ： disable ONU port |
configure ONU Uni port auto-nego
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc auto-nego <oper> |
| Function | enable or disable ONU uni port auto-nego |
| <oper> | value <enable | disable>：
enable: enable ONU uni port auto-nego disable: disable ONU uni port auto-nego |
configure ONU Uni port flow-ctrl
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc flow-ctrl <oper> |
| Function | enable or disable ONU uni port flow-ctrl. |
| <oper> | value <enable | disable>：
enable ： enable ONU uni port flow-ctrl disable ： disable ONU uni port flow-ctrl |
Configure ONU Uni port Egress Rate
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc egress-policing < max-rate> |
| Function | configure ONU uni port egress rate 。 |
| < max-rate> | designate max traffic ouput rate with value<0~1000000>kbps， a value of 0 indicates no speed limit. |
Configure ONU Uni port ingress Rate
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc ingress-policing < max-rate> |
| Function | configure ONU uni port ingress rate. |
| < max-rate> | designate max traffic input rate with value<0~1000000>kbps ，
a value of 0 indicates no speed limit |
Configure ONU Uni port MAC agine-time
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc mac-aging-time <timer> |
| Function | configure ONU uni port MAC aging-time. |
| < timer > | designate the MACs aging-time with value 0-4294967295
， a value of 0 indicates the MAC address is not aging 。 |
configure ONU Uni port statistics
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc statistics <monitoring-status>
<monitoring-period> |
| Function | Configure statistics monitoring status and period. |
| <monitoring- status> | designate statistics monitoring status with value <enable | disable> enable: enable statistics monitoring
disable: disable statistics monitoring |
| <monitoring- period> | designate statistics monitoring status with value <1- 4294967295>second |
Configure ONU Uni Port Vlan Mode
Configure ONU Uni port VLAN aggregation mode （ Our company does not support ONU）
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc vlan-mode aggregation <tpid> <cos>
<default-vlan> aggregation-list（Matching） |
| Function | configure the ONU uni port VLAN for aggregation mode. |
| <tpid > | designate vlan tpid ， the default is 0x8100. |
| <cos> | designate vlan cos ， valid value <0-7>. |
| <vlan> | designate ONU uni port aggregation mode vlan ， valid value <1- 4094> ， the default is 1. |
| Aggregation- list | designate ONU uni port aggregation vlan list，maximum support 4. |
【 Example 】
Example1： For the ONU uni port configuration VLAN mode for aggregation, 100 for default- vlan
Configure ONU Uni port VLAN tag mode
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc vlan-mode tag <tpid> <cos> <vlan> |
| Function | configure the ONU uni port VLAN for tag mode. |
| <tpid > | designate vlan tpid ， the default is 0x8100. |
| <cos> | designate vlan cos ， valid value <0-7>. |
| <vlan> | designate ONU uni port tag mode vlan ， valid value <1- 4094> ， the default is 1 |
【 Example 】
|
Example1：For the ONU uni port configuration VLAN mode for tag, 100 for VLAN
Configure ONU Uni port VLAN trunk mode
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc vlan-mode trunk <tpid> <cos>
<default-vlan> vlan-list （Matching） |
| Function | configure the ONU uni port VLAN for trunk mode. |
| <tpid > | designate vlan tpid ， the default is 0x8100 |
| <cos> | designate vlan cos ， valid value <0-7>. |
| <vlan> | designate ONU uni port trunk mode vlan ， valid value <1- 4094> ， the default is 1. |
| Vlan-list | Optional configuration, configuration can be through the VLAN list, the maximum support 60 VLAN number. |
【 Example 】
Example1： For the ONU uni port configuration VLAN model for trunk, 100 for default-vlan, 200,2050 for vlan-list
Configure ONU Uni port VLAN translation mode
| Command Gramma | epon(olt-7/onu-1/uni-1)#ctc vlan-mode translation <tpid> <cos>
<default-vlan> translate-list |
| Function | configure the ONU uni port VLAN for translation mode. |
| <tpid > | designate vlan tpid ， the default is 0x8100. |
| <cos> | designate vlan cos ， valid value <0-7>. |
| <vlan> | designate ONU uni port translation mode vlan ， valid value <1- 4094> ， the default is 1. |
| translation-list | The specified uni port list of VLAN, maximum support 8 conversion list. |
【 Example 】
Example1： For the ONU uni port configuration mode of VLAN translation, default-vlan 100, translation-list 200-300 300-400
Configure ONU Uni port VLAN transparent mode
| Command | epon(olt-7/onu-1/uni-1)#ctc vlan-mode transparent |
| Gramma | |
| Function | configure the ONU uni port VLAN for transparent mode. |
【 Example 】
|
Example1： For the ONU uni port configuration VLAN mode for transparent
【Description 】
Different VLAN mode to deal with different frame types.
|
- Transparent Mode ：
|
- Tag Mode：
|
- Translation Mode ：
| Downstrea m | Untag frame | Discard the frame |
| Tag frame | Tag frame VLAN ID corresponds to the entry in the
corresponding port of the VLAN Translation list (equal to the input VID configuration) ， According to the table to convert the VID to a corresponding VID (VID output), forwarding; If the VLAN ID in the corresponding port of the VLAN Translation list without a corresponding entry, discarding; If the TAG frame with VLAN ID as the “default VLAN”, after the VLAN label forwarding is stripped down; |
|
- Trunk Mode：
Show ONU Uni port vlan configuration
| Command Gramma | epon(olt-7/onu-1/uni-1)#show olt 7 onu 1 uni 1 ctc vlan-mode |
| Function | Show ONU uni port vlan configuration |
【 Example 】
|
Example1： Show ONU uni port vlan configuration ：
Enter ONU VOIP Port Management Mode
| Command Grammar | epon(olt-7/onu-1)# pots <pots> |
| Function | enter the ONU voip port management mode to configure the ONU uni parameter. |
| < pots> | designate ONU voip port with valid value <1-2>. |
【 Example 】
|
Example1： enter the ONU VOIP port 1 management mode ：
epon(olt-7/onu-1/pots-1)# ？ input ”?” to show the following directory:
ctc – ctc management mode
exit – exit current mode Global command:
logout – exit the CLI system
ping – test that a remote host is reachable
show – show system configuration
tracert – trace the route to host
Configure ONU VOIP Port Parameters
Show ONU VOIP port work status
| Command Gramma | epon(olt-7/onu-1/pots-1)# show olt 7 onu 1 pot 1 ctc status |
| Function | Using the command in any mode,can display the current ONU VOIP port parameter properties. |
【 Example 】
|
Example1： show ONU VOIP port 1 work status
Enable/disable the ONU VOIP port
| Command Gramma | epon(olt-7/onu-1/pots-1)# ctc admin <admin> |
| Function | Enable or disable the onu voip port |
| < admin> | <enable | disable> ：
enable open the voip port disable close the voip port |
【 Example 】
|
Example1：enable the ONU1 VOIP port 1
Configure the VOIP port H.248 user TID
| Command Gramma | epon(olt-7/onu-1/pots-1)# ctc h248-user-tid <User-TID> |
| Function | Configure the VOIP port h.248 user TID |
| < User-TID> | String, length :32 chars |
【 Example 】
|
Example1： configure ONU 1 VOIP 1 H.248 user TID is 100
Configure the VOIP port sip user parameter
| Command Gramma | epon(olt-7/onu-1/pots-1)# ctc sip-user-config <user-account> <user- name> <user-password> |
| Function | Configure ONU voip port SIPuser parameter |
| < user-account> | The number of user ， string length:16 chars |
| <user-name> | User name ， string length:32 chars |
| <user- password> | User password， string length:32 chars |
【 Example 】
|
Example1：add a user in onu 1 voip port 1, the name is 222, the password is 222
8 Equipment diagnosis information
Ping command test
| Command Grammar | epon# ping <host> |
| Function | Test equipment and network can reach the target host |
| <host> | Host ip address |
【 Example 】
Example1：device ip: 192.168.1.100，host ip 192.168.1.234 host and device are The direct connection
Tracert checking the device the path of the host
| Command Grammar | epon# tracert <host> |
| Function | Check the device the path of the host |
| <host> | Host ip address |
【 Example 】
Example1 ： checking the device the path of the host 。
